国外购物网站怎么做,房地产网页设计网站建设,用flash做网站建设,dede网站模板 医疗华为交换机VLAN内Proxy ARP配置示例1、组网需求图1 VLAN内Proxy ARP组网示例图如上图1所示#xff0c;Switch的接口GE1/0/2和GE1/0/1属于同一个sub-VLAN2。该sub-VLAN属于super-VLAN3。要求#xff1a;属于同一VLAN2的两台主机hostA和hostB之间二层隔离。hostA和hostB之间通过…华为交换机VLAN内Proxy ARP配置示例1、组网需求 图1 VLAN内Proxy ARP组网示例图如上图1所示Switch的接口GE1/0/2和GE1/0/1属于同一个sub-VLAN2。该sub-VLAN属于super-VLAN3。要求属于同一VLAN2的两台主机hostA和hostB之间二层隔离。hostA和hostB之间通过VLAN内Proxy ARP实现三层互通。Super-VLAN的VLANIF接口的IP地址为10.10.10.1子网掩码为255.255.255.0。2、配置思路2.1、创建和配置Super-VLAN和Sub-VLAN。2.2、将接口加入到从Sub-VLAN中。2.3、创建Super-VLAN的VLANIF接口并配置其IP地址。2.4、在Super-VLAN的VLANIF接口使能VLAN内Proxy ARP(arp代理)功能。3、操作步骤3.1、配置Super-VLAN和Sub-VLAN。# 配置Sub-VLAN2。 system-view[HUAWEI] vlan 2[HUAWEI-vlan2] quit# 使能GE1/0/1和GE1/0/2端口隔离功能。[HUAWEI] port-isolate mode l2[HUAWEI] interface gigabitethernet 1/0/1[HUAWEI-GigabitEthernet1/0/1] port-isolate enable[HUAWEI-GigabitEthernet1/0/1] quit[HUAWEI] interface gigabitethernet 1/0/2[HUAWEI-GigabitEthernet1/0/2] port-isolate enable[HUAWEI-GigabitEthernet1/0/2] quit# 将GE1/0/1和GE1/0/2加入到Sub-VLAN2中。[HUAWEI] interface gigabitethernet 1/0/1[HUAWEI-GigabitEthernet1/0/1] port link-type access[HUAWEI-GigabitEthernet1/0/1] port default vlan 2[HUAWEI-GigabitEthernet1/0/1] quit[HUAWEI] interface gigabitethernet 1/0/2[HUAWEI-GigabitEthernet1/0/2] port link-type access[HUAWEI-GigabitEthernet1/0/2] port default vlan 2[HUAWEI-GigabitEthernet1/0/2] quit# 配置Super-VLAN3并将Sub-VLAN2增加到Super-VLAN中。[HUAWEI] vlan 3[HUAWEI-vlan3] aggregate-vlan[HUAWEI-vlan3] access-vlan 2[HUAWEI-vlan3] quit3.2、创建和配置接口VLANIF3。# 创建接口VLANIF3。[HUAWEI] interface vlanif 3# 配置接口VLANIF3的IP地址。[HUAWEI-Vlanif3] ip address 10.10.10.1 243.3、在接口VLANIF3启动VLAN内Proxy ARP。[HUAWEI-Vlanif3] arp-proxy inner-sub-vlan-proxy enable[HUAWEI-Vlanif3] quit4、检查配置结果4.1、执行命令display current-configuration查看Super-VLAN、Sub-VLAN以及VLANIF接口的相关配置。查询结果请见下面给出的配置文件。4.2、 hostA和hostB互相可以Ping通。5、配置文件以下仅给出Switch的配置文件。#sysname HUAWEI#vlan batch 2 to 3#vlan 3 aggregate-vlan access-vlan 2#interface Vlanif3 ip address 10.10.10.1 255.255.255.0 arp-proxy inner-sub-vlan-proxy enable#interface GigabitEthernet1/0/1 port link-type access port default vlan 2 port-isolate enable group 1#interface GigabitEthernet1/0/2 port link-type access port default vlan 2 port-isolate enable group 1#return
